PCIe 2-Port 10G 6-Speed Multi-Gigabit Network Adapter

This card is a high-performance, 2 ports, 6-speed, 10 Gigabit Adapter designed for low-power, low-cost connectivity required
by application servers, high-end workstations and personal computers.

It delivers up to 10 Gbps network connectivity speed through 100m of Cat 6a cabling. It also supports up to 5 Gbps network
connectivity speed on legacy Cat 5e or Cat 6 cabling

Features

• Support 6-Speed 10Gb/5Gb/2.5Gb/1Gb/100Mb/10Mb auto- negotiation
• PCI Express 3.0 x4
• Compliant with IEEE 802.3bz, 802.3an
• Energy Efficient Ethernet (EEE)
• Up to 16K Jumbo Frames
• IP, TCP, UDP checksum offload
• Support WOL

Requirements Hardware

• The following system specs are recommended minimum
• PCIe slot: Available 4-Lanes PCI-Express slot Gen 4, Gen 3 or Gen 2
• Processor: Quad Core 3.0GHz or higher
• RAM: 4GB memory or higher

Software

• Operating systems supported are (both 32 and 64 bits)
• Windows 8.x, 10, 11
• Linux 3.10 or later

Package Contents

• • 1 x PCIe 2- Port 10G 6-Speed Multi-Gigabit Network Adapter
  • 1 x User Manual

הפוסט PCIe 2-Port 10G Multi-Gigabit הופיע לראשונה ב-NBtech Group.

PCIe Dual Ports LAN Card

Description:

PCI Express is the next revolution in I/O interconnect standards that will deliver the bandwidth
and features required by PCs, consumer electronics and communications devices.

The architecture is a cost-effective, low-pin count, and point-to-point technologies offering maximum
bandwidth, reducing cost and design complexity and enabling smaller form factors.

This card is the best solution for Gigabit Ethernet PCI Express and the interface has a potential transfer
rate of 2.5 Gbps using a single-lane (or x1) PCI Express link.

This card is a 2-Port Gigabit Ethernet PCI Express Card, which is specifically designed to plug into a
desktop equipped with an available x1, x4, x8 or x16 PCI Express slot.

It supports high performance dual channel networking and full duplex communication to achieve up to
2000 Mbps and fast transfer rates, yet is compatible with existing Ethernet.

It comes with a comprehensive of software drives for all desktop operating systems, including Microsoft
Windows and Linux.

Features

• Designed to meet PCI Express Specification Revision 2.1
• Single-lane (or x1) PCI Express throughput supports rate of 2.5Gbps
• Fully Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• Supports 10/100/1000M data auto-negotiation
• Automatic MDI/MDIX crossover at all speeds
• Up to 9K jumbo frame support
• Supports Wake On Lan (WOL) power management
• Features full duplex mode that doubles the network connections speed

System Requirements

• Windows 7/8.x/10/11, Windows Server 2008 R2/2012 R2/2016/2019
• Linux 2.6.x or later
• PC with one free PCIe slot

Package Contents

• 1 x 2-Port Gigabit Ethernet PCIe Card
• 1 x User Manual

הפוסט PCIe Dual Ports LAN Card הופיע לראשונה ב-NBtech Group.

USB 3.1 Gen2 Type-C – 4 Port Hub (3A+1C)

Color: White

Overview:

The USB 3.1 Gen2 A+C 4-Port Hub features four USB 3.1 ports for use with a MacBook or Pixel,
extending functionality for connecting other devices.

3 x USB 10Gbps Type-A port
1 x USB 10Gbps Type-C port
Supports BC1.2 and Apple charging

Features

• Expand the connectivity of your computer using the latest USB 3.1 Gen 2 technology
• Plug the USB 3.1 Type-C Pocket Hub into an available USB Type-C port on your computer
• Provides three Type-A and one Type-C downstream ports
• Supports BC1.2 and Apple charging
• Compliant with USB 3.1 Gen2 and data rate up to 10Gbps
• Backward compatible with USB3.1 Gen1 (USB3.0),USB2.0 and USB1.1 devices
• Hot-swapping feature allows you to connect/disconnect devices without powering down the system
• LED to indicate Hub power

System Requirements

• Windows 7/8/8.1/10 (32/64 bit)
• Mac OS X v10.8 or later
• Linux 2.6.24 and 4.11.x or later

Package Contents

• 1 x USB 3.1 Gen2 A+C 4Port Hub
• 1 x User Manual

הפוסט USB 3.1 Gen2 Type-C – 4Port Hub הופיע לראשונה ב-NBtech Group.

PCIe 10G 5-Speed Multi-Gigabit Network Card

Description:

This card is a Multi-Gigabit network adapter that runs on a high speed PCIe x4 host but interface.

This card hosts the Tehuti new 3rd generation TN4010 controller, and optimized 10 Gigabit Ethernet
MAC designed for low-power, low-cost, single-port connectivity required by Application Servers and
Workstations. The TN4010 MAC is paired with Marvell Alaska 88X3310P transceiver, a low-power,
high-performance 10 Gigabit Ethernet PHY, to enable five-speed connectivity (10GBase-T, 5GBase-T
2.5GBase-T 1000Base-T, and 100Base-TX) over low-cost  standard CAT-6a Ethernet cabling, up to
100m (Cat-5e and CAT-6 are supported compliant to Link Segment specifications).

This combination creates a new gateway to cost-conscious consumer applications, as well as to
intensive data environments.

Features

• Supports 10G/5G/2.5G/1G/100M
• Runs up to 10G at 100m Cat 6A cable and 5G at 100m Cat 5e/Cat 6 cable
• Backward compatibility with 1000Base-T, 100Base-T Networks
• PCI Express Gen-2 x4 Host Bus interface
• EEE (Energy Efficient Ethernet)
• 9K Jumbo Frames
• IP, TCP, UDP checksum offloading
• IEEE 802.1Q Tagged VLAN
• Virtual NIC support
• Reduced CPU utilization and improved throughput

Requirements

Hardware

• The following system specs are recommended minimum
• PCIe slot: Available 4-Lanes PCI-Express slot gen 2.0 or later
• Processor: Quad Core 3.0GHz or higher
• RAM: 4GB memory or higher

Software

• Operating systems supported are (both 32 and 64 bits)
• Windows 7
• Windows Server 2008 R2
• Windows Server 2012
• Windows 8.1
• Windows Server 2012 R2
• Windows 10
• Linux 2.6.24 or later
• VMware ESXi 5.x/6.0
• Mac OS X 10.12.6 or later

Package Contents

• 1 x PCIe 10G 5-Speed Multi-Gigabit Network Card
• 1 x Driver CD
• 1 x User Manual

הפוסט PCIe 5-Speed Network Card הופיע לראשונה ב-NBtech Group.

Producer: ST-LAB

Color: White

Overview:

The USB 3.1 Gen2 Type-A 4-Port Hub features four USB 3.1 ports for use with a MacBook or Pixel,
extending functionality for connecting other devices.

Features

Expand the connectivity of your computer using the latest USB 3.1 Gen 2 technology

Plug the USB 3.1 Type-C Pocket Hub into an available USB Type-C port on your computer

Provides three Type-A and one Type-C downstream ports

Supports BC1.2 and Apple charging

Compliant with USB 3.1 Gen2 and data rate up to 10Gbps

Backward compatible with USB3.1 Gen1 (USB3.0),USB2.0 and USB1.1 devices

Hot-swapping feature allows you to connect/disconnect devices without powering down the system

LED to indicate Hub power

System Requirements

Windows 7/8/8.1/10 (32/64 bit)

Mac OS X v10.8 or later

Linux 2.6.24 and 4.11.x or later

Package Contents

1 x USB 3.1 Gen2 A+C 4-Port Hub

1 x User Manual

Download driver from ST-LAB website – here

הפוסט USB 3.1 Gen2 Type-A – 4 Port Hub הופיע לראשונה ב-NBtech Group.